🇻🇳 Lỗi SC552 trên Ricoh MP 4002 / MP 5002 – Nhiệt sấy không đạt yêu cầu
Mã lỗi: SC552
Tên lỗi: Lỗi khởi động nhiệt sấy – Fusing temperature warm-up error (end)
Trên các dòng máy Ricoh MP 4002 và MP 5002, mã lỗi SC552 xuất hiện khi bộ sấy (fusing unit) không đạt đủ nhiệt độ cần thiết trong thời gian quy định khi máy khởi động.
Điều kiện xảy ra lỗi:
- Cảm biến nhiệt (thermistor) ở đầu sấy không ghi nhận được mức tăng 8°C trong 7,5 giây sau khi nhiệt độ đạt 45°C.
- Hoặc cảm biến ở đầu sấy không đạt được nhiệt độ mục tiêu trong vòng 31 giây kể từ khi bóng đèn sấy (heater lamp) bắt đầu hoạt động.
Nguyên nhân thường gặp:
- Cảm biến nhiệt bị cong, lệch vị trí hoặc hỏng.
- Kết nối giữa cảm biến và bảng điều khiển không ổn định.
- Bộ sấy bị bụi bẩn hoặc bề mặt tiếp xúc kém.
- Bóng đèn sấy bị cháy hoặc không phát đủ nhiệt.
Cách khắc phục đề xuất:
- Tắt nguồn máy và để nguội hoàn toàn trước khi thao tác.
- Kiểm tra cảm biến nhiệt (thermistor), làm sạch bụi bẩn hoặc thay mới nếu hư.
- Kiểm tra hệ thống dây kết nối và giắc cắm giữa cụm sấy với bo mạch chính.
- Kiểm tra hoạt động của bóng đèn sấy – nếu không sáng, cần thay thế.
- Sau khi sửa xong, vào Service Mode → 5810 để xóa lỗi và khởi động lại máy.
💡 Mẹo kỹ thuật: Giữ cho cụm sấy luôn sạch và thoáng khí sẽ giúp kéo dài tuổi thọ linh kiện và hạn chế lỗi SC552 xuất hiện lại.
🇬🇧 Ricoh MP 4002 / MP 5002 – Error SC552: Fusing Warm-Up Temperature Fault
Error Code: SC552
Error Name: Fusing temperature warm-up error (end)
On Ricoh MP 4002 and MP 5002 copiers, error SC552 indicates that the fusing unit has failed to reach the correct temperature during the warm-up phase.
When the error occurs:
- The end thermistor fails to detect an 8°C temperature rise within 7.5 seconds after the fusing unit reaches 45°C.
- Or the thermistor temperature does not reach the target value within 31 seconds after the fusing lamp turns on.
Main Causes:
- The thermistor is warped, misaligned, or defective.
- Loose or faulty wiring between the thermistor and control board.
- Poor contact or contamination inside the fusing unit.
- Burned-out fusing lamp or insufficient heat generation.
Recommended Fixes:
- Turn off the machine and allow it to cool down.
- Inspect and clean the thermistor; replace it if damaged.
- Check all wiring and connectors between the fusing unit and main controller.
- Test the fusing lamp to ensure it lights up properly.
- After repairs, enter Service Mode → 5810 then restart the machine.
💡 Pro Tip: Keeping the fusing unit clean and well-ventilated reduces the risk of future SC552 errors and ensures stable performance.
