⚠️ Lỗi SC400 trên máy photocopy Ricoh MP 4001 / 5001 / 4002 / 5002
🔍 Mô tả lỗi (Description)
Lỗi SC400 – Vsg Adjustment Error xuất hiện khi giá trị Vsg (Voltage Sensor Gray) bị sai lệch trong quá trình máy tự động cân chỉnh cảm biến ID.
Cụ thể, lỗi xảy ra khi giá trị Vsg cao hơn 4.2V hoặc thấp hơn 3.8V, khiến hệ thống không thể đo chính xác mật độ mực (toner density).
⚙️ Nguyên nhân gây lỗi (Causes)
-
🧹 Cảm biến ID (ID Sensor) bị bẩn hoặc hỏng
– Bụi mực, bụi giấy hoặc cặn bám làm cảm biến đo sai giá trị Vsg.
– Nếu cảm biến xuống cấp hoặc cháy mạch, tín hiệu điện áp trả về sai lệch. -
⚙️ Cửa che cảm biến (ID Sensor Shutter) hoạt động không đúng
– Cửa che bị kẹt, không mở hoàn toàn hoặc không đóng kín khiến cảm biến nhận sai ánh sáng phản xạ.
🧰 Cách xử lý lỗi SC400 Ricoh MP 4001 – 5002
✅ Bước 1: Tắt nguồn, rút dây điện để đảm bảo an toàn.
✅ Bước 2: Mở nắp trước → tháo cụm trống (Drum Unit) ra ngoài.
✅ Bước 3: Tìm cảm biến ID (nằm ở phía dưới cụm Drum, gần cụm phát hiện mực).
✅ Bước 4:
- Dùng bông tăm và cồn isopropyl lau sạch mặt cảm biến.
- Kiểm tra cửa che cảm biến (shutter) có hoạt động trơn tru không.
✅ Bước 5: Gắn lại cụm Drum, khởi động máy.
✅ Bước 6: Vào Service Mode → SP2-801 (VSG Adjustment) để chạy lại quy trình cân chỉnh cảm biến.
✅ Bước 7: Nếu vẫn báo lỗi, thay ID Sensor mới chính hãng Ricoh.
🧠 Lưu ý quan trọng
- Vệ sinh cảm biến định kỳ mỗi 30.000–50.000 bản in.
- Không dùng vật cứng chà lên mặt cảm biến.
- Nếu máy thường xuyên bám bụi mực, nên kiểm tra cụm gạt mực và developer.
⚙️ English Version: SC400 Error on Ricoh MP 4001 / 5001 / 4002 / 5002
🔎 Error Description
SC400 – Vsg Adjustment Error occurs when the Vsg (Voltage Sensor Gray) reading is out of range during automatic ID sensor calibration.
The machine detects this error if the Vsg voltage is greater than 4.2V or less than 3.8V, preventing proper toner density adjustment.
🛠️ Possible Causes
- Dirty or defective ID sensor → Dust or toner buildup causes incorrect readings.
- Defective ID sensor shutter → The shutter may be stuck or misaligned, blocking proper light reflection to the sensor.
🔧 How to Fix SC400 Error
- Power off and unplug the copier.
- Open the front cover and remove the drum unit.
- Locate the ID Sensor under the drum assembly.
- Clean the sensor surface with isopropyl alcohol and a soft swab.
- Ensure the shutter moves freely without obstruction.
- Reinstall all units and restart the copier.
- Enter Service Mode → SP2-801 (Vsg Adjustment) to recalibrate.
- If the error persists, replace the ID Sensor.
💡 Maintenance Tips
- Regularly clean the ID sensor to prevent toner accumulation.
- Avoid low-quality toner that may generate excessive dust.
- Keep the developer and drum area clean for accurate readings.
🔑 Từ khóa SEO gợi ý:
Ricoh MP 4001 SC400, Ricoh MP 5001 lỗi SC400, Ricoh MP 4002 Vsg Adjustment Error, Ricoh MP 5002 ID Sensor lỗi, SC400 Ricoh fix, lỗi Vsg Ricoh MP.
