⭐ BẢN TIẾNG VIỆT –
SC360-01 – Lỗi hiệu chỉnh cảm biến tỷ lệ mực (TD Sensor Adjustment Error)
Trên các dòng Ricoh MP 2555 / 3055 / 3555 / 4055 / 5055 / 6055, mã SC360-01 xuất hiện khi hệ thống đánh giá mật độ mực – từ trong cụm phát triển (developer) thông qua cảm biến TD và phát hiện giá trị đo nằm ngoài dải cho phép. Nếu ba lần liên tiếp cảm biến trả về số liệu lệch khỏi mức tham chiếu hoặc máy xác định trạng thái thiếu developer, máy sẽ ngừng hoạt động để bảo vệ cụm từ.
🔍 Nguyên nhân khả dĩ
1. Cảm biến TD gặp sự cố
- Cảm biến suy hao, đọc sai giá trị hoặc cho tín hiệu nhiễu.
- Lỗi phần cứng khiến cảm biến không phản hồi đúng khi máy hiệu chỉnh.
2. Kết nối truyền tín hiệu kém ổn định
- Giắc kết nối của TD sensor lỏng hoặc tiếp xúc không chặt.
- Dây dẫn giữa cảm biến và bo mạch bị đứt ngầm hoặc gãy lõi.
3. Developer không phù hợp hoặc đã suy giảm
- Bột từ sau thời gian sử dụng bị vón, bị ẩm hoặc giảm chất lượng.
- Developer được thay mới nhưng loại mực sử dụng không đồng nhất với tiêu chuẩn ban đầu.
- Tỷ lệ mực–từ (toner/developer ratio) lệch quá xa so với mức tiêu chuẩn khiến Mu count vượt ngưỡng.
🛠 Cách khắc phục đề xuất (đều viết mới)
- Thay dây dẫn cảm biến TD nếu phát hiện chập, đứt hoặc trở kháng bất thường.
- Cắm lại đầu nối cảm biến để đảm bảo tiếp xúc điện tốt.
- Thay cảm biến TD khi không thể hiệu chỉnh hoặc giá trị trả về sai lệch hoàn toàn.
- Thay toàn bộ cụm phát triển (development unit) nếu developer mất tính chất hoặc bột từ không còn đạt chuẩn.
⭐ ENGLISH VERSION
SC360-01 – TD Sensor Calibration Failure
For the Ricoh MP 2555–6055 series, the SC360-01 code is triggered when the machine attempts to calibrate the toner density inside the development unit and the TD sensor repeatedly reports abnormal readings. If the measured Mu value exceeds the limit for a “no developer” condition or remains outside the specified upper and lower bounds for three consecutive cycles, the machine issues the error.
🔍 Likely Causes
1. Faulty TD sensor
- Sensor output fluctuates or fails to deliver accurate density readings.
- Internal sensor components degrade, leading to unstable calibration values.
2. Wiring and connector issues
- Loose or unstable connector contact between the TD sensor and the control board.
- Harness damage such as broken strands or insulation wear.
3. Developer condition problems
- Developer inside the unit deteriorates, becoming compacted or inconsistent.
- Mixing different types of toner/developer causing incorrect density ratios.
- Improper toner concentration causing Mu values outside acceptable tolerance.
🛠 Recommended Fixes
- Replace the TD sensor harness if continuity is unstable.
- Re-seat the connector to restore proper communication.
- Install a new TD sensor when readings cannot be corrected.
- Replace the entire development unit if the developer mixture is no longer usable.
